Straight Razor Gear

Straight Razor Widths: Choosing Between 4/8 and 8/8

Straight razor sizes explained, from 4/8 to 8/8: how width is measured, 5/8 vs 6/8 compared, how size affects weight, lather and honing, and which to choose.

On this page
  1. How straight razor width is measured
  2. Widths at a glance
  3. 5/8 vs 6/8: the main decision
  4. Smaller blades: 4/8 and 5/8
  5. Larger blades: 7/8 and 8/8
  6. How width affects honing
  7. Width works with grind and point
  8. Which width should you choose?

Straight razor width is one of the first specs you’ll see when shopping. It changes how a razor feels, how much lather it holds, and how easily it gets into tight spots.

How straight razor width is measured

Width is the distance from the spine to the edge, measured in eighths of an inch. A “5/8” razor is five-eighths of an inch wide, about 16 mm. One eighth of an inch is about 3.2 mm.

Width Approximate metric
4/8 (1/2 inch) 12.7 mm
5/8 15.9 mm
6/8 (3/4 inch) 19.1 mm
7/8 22.2 mm
8/8 (1 inch) 25.4 mm

Razors wider than 8/8 exist but are uncommon. Very narrow blades (around 3/8 and below) are mostly hairdressing or specialty razors.

Vintage razors may have been honed narrower over the years, so a razor stamped 6/8 may now measure a little less.

Widths at a glance

Width Feel Good for
4/8 Light, nimble Tight spots, small faces, detail work, travel
5/8 Balanced, the most common size Most beginners and general use
6/8 A little heavier, holds more lather General use; some prefer for heavier beards
7/8 Heavy, stiff, lots of lather capacity Experienced shavers who like a big blade
8/8 Very large and heavy Enthusiasts and collectors

5/8 vs 6/8: the main decision

Most buyers end up choosing between these two, and both are good first razors.

5/8:

  • The most common and widely available size
  • Slightly lighter and easier to manoeuvre under the nose and around the chin
  • Usually the default recommendation for beginners

6/8:

  • A bit more weight, which some shavers find steadies the stroke
  • Holds more lather, so you may rinse less often
  • A touch less nimble in tight spots, though most people adapt quickly

If you have no strong preference, a 5/8 is the safe choice. If you like a bit more heft, or have a large face and dense beard, a 6/8 is a reasonable alternative. Many shavers eventually own both.

Smaller blades: 4/8 and 5/8

Smaller blades are light and agile, which helps under the nose, around the lips and along tight jawlines. The trade-offs are that they hold less lather (more rinsing) and have less weight behind the stroke. A 4/8 can be a nice second razor for detail work, such as lining up a beard, or travel, but most people find 5/8 more versatile as a first razor.

Larger blades: 7/8 and 8/8

Large blades are heavy and stiff and carry a lot of lather. Some experienced shavers enjoy the feel and find big blades efficient on cheeks and necks. They can be awkward under the nose and around the mouth, and the weight takes getting used to. They’re usually not recommended as a first razor.

How width affects honing

Width interacts with spine thickness to set the bevel angle when the razor lies flat on a stone. For the same spine thickness, a wider blade gives a more acute bevel angle, and a narrower blade a more obtuse one. Makers design spine thickness with this in mind, so it’s mostly a concern with vintage razors that have heavy hone wear, or when deciding whether to add tape to the spine.

Larger blades also have more steel to keep flat, and any warp or curve along the edge tends to be more noticeable on the stone. See our guide to honing a straight razor on whetstones.

Width works with grind and point

Width is only part of how a razor feels:

  • Grind: a 6/8 full hollow can feel lighter than a 5/8 wedge. See straight razor grinds explained.
  • Point: a round point is more forgiving; a square point is more precise but easier to nick with.
  • Scales and balance: affect how the razor sits in your hand.

Which width should you choose?

  • First razor: 5/8, or 6/8 if you prefer a bit more weight.
  • Detail work or a small face: consider a 4/8 or 5/8.
  • You like heavy tools and have experience: try a 7/8 or 8/8.

For the other specs to consider, see our guide to the best straight razors.

The complete guide to straight razor gear

Best Straight Razors
Read the guide

Keep exploring

Guides from other topics

All topics →