Straight Razor Gear

How to Hone a Straight Razor on Whetstones

Step-by-step straight razor honing on whetstones: choosing a grit progression, flattening stones, the honing stroke, setting the bevel, finishing, testing and fixes.

On this page
  1. Before you start: do you need a full honing?
  2. What you need
  3. Prepare and flatten the stones
  4. The honing stroke
  5. Step 1: set the bevel
  6. Step 2: refine through the grits
  7. Step 3: finish and strop
  8. Test the edge
  9. Troubleshooting
  10. When to use a honing service instead

Honing restores the edge of a straight razor when stropping alone no longer keeps it shaving comfortably. It takes patience to learn, but the technique is simple: light pressure, a flat stone, and a consistent stroke.

If you’re new to honing, practise on an inexpensive razor first, not a treasured one. If you’re not sure what an old razor is worth, see are old cut-throat razors valuable?.

Before you start: do you need a full honing?

Not every dull razor needs a full progression from a coarse stone.

  • A razor that has shaved well but is starting to tug may only need a touch-up on a fine finishing stone or a pasted strop.
  • A new razor that isn’t shave ready, a vintage razor, or one with a chip or a rolled edge usually needs the bevel set on a coarser stone and a full progression.

Our guide to how to tell when a straight razor needs honing explains how to judge this.

What you need

A stone progression

A common synthetic progression looks something like this:

  • Around 1,000 grit: for setting the bevel (establishing a clean, meeting edge) and removing small chips.
  • Around 3,000 to 5,000 grit: for refining the edge and removing the coarser scratches.
  • Around 8,000 grit: for polishing.
  • Around 10,000 to 12,000 grit or higher: for finishing.

Exact grit numbers vary between brands, and there are many valid progressions. A combination stone with roughly 4,000 and 8,000 grit sides is a popular and economical choice for maintaining a razor that already has a good bevel. Natural finishing stones are also widely used, though they vary from stone to stone.

Flattening tool

Stones wear unevenly with use. A razor needs a flat stone because the spine and edge both ride on the surface. A lapping plate, diamond plate or fine wet-and-dry paper on a flat surface keeps your stones flat.

Tape (optional)

Some honers put one or two layers of electrical tape along the spine. This reduces wear on the spine and slightly raises the bevel angle. It’s optional, but if you use tape, use the same amount every time on that razor, or you’ll have to reset the bevel.

You’ll also need water (or the lubricant your stones call for), a towel, and a strop for afterwards.

Prepare and flatten the stones

  1. Soak or splash the stones as their maker recommends. Some need soaking; others only need surface water.
  2. Draw a pencil grid on the surface.
  3. Rub the stone on your flattening plate until the grid disappears evenly. If some lines remain, that part is low; keep going.
  4. Lightly chamfer (bevel) the stone’s edges so they don’t catch the razor.
  5. Rinse off any grit before honing.

The honing stroke

  1. Lay the razor flat on the stone, with both the spine and the edge touching. The spine sets the angle; don’t lift it.
  2. Push the razor edge first along the stone, with very light pressure. Let the stone do the work.
  3. Use an X stroke. Most razors are longer than a stone is wide, so move the razor diagonally as it travels: heel of the blade at the start of the stroke, toe at the end. This keeps the whole edge, heel to point, in contact.
  4. Roll over the spine at the end of each stroke. Turn the razor over on its spine, never on its edge, then stroke back in the other direction.
  5. Keep the strokes even. Same number on each side, same pressure, same pattern.

The edge-leading direction on the stone is the opposite of stropping, where the spine leads.

Step 1: set the bevel

On your coarsest stone, use the X stroke with light pressure until both bevels meet at a clean, consistent edge along the full length. How many strokes this takes varies widely, from a few dozen for a razor that’s nearly there to many more for a damaged edge.

Ways to check:

  • Marker test: colour the bevel with a permanent marker, take a few strokes, and see where the ink has been removed. Even removal along the edge means good contact.
  • Light test: look straight down at the edge under a bright light. A dull or unfinished edge reflects light as a shiny line or spots; a well-set edge shows almost nothing.
  • Gentle hair test: a properly set bevel should start to cut arm hair at or just above skin level. Do this carefully.

Don’t move on until the bevel is set. A poorly set bevel is the most common reason an edge never gets sharp, no matter how fine the finishing stones.

Step 2: refine through the grits

Move to the next stone and repeat with light X strokes until the scratches from the previous stone are replaced by finer ones. Many honers use somewhere between a few dozen and around a hundred laps per stone, but the number matters less than the result. Rinse the razor between stones so coarse grit isn’t carried onto finer stones.

Some honers reduce pressure further on each stone and finish with very light, “weight of the razor only” strokes.

Step 3: finish and strop

On your finishing stone, use very light strokes to polish the edge. Then strop: a few laps on linen or canvas and a set of laps on leather, spine leading, light pressure. Our guide to leather strops covers technique.

Test the edge

  • Hanging hair test: a sharp edge should cut a hanging hair close to where you hold it, without the hair simply bending away.
  • Arm hair test: the razor should cut arm hair above the skin, with little or no contact.
  • The shave test: the only conclusive test. Shave a small area, with the grain, and note any tugging.

Always test carefully and keep fingers well away from the edge.

Troubleshooting

  • Razor still tugs after the full progression: the bevel may not have been fully set. Go back to the bevel-setting stone.
  • Only part of the edge is sharp: the razor may have a slight smile, frown or warp, or your X stroke isn’t covering the full edge. Adjust the stroke, using a slight rolling motion for curved edges.
  • Edge feels harsh: too much pressure on the finishing stone, or stropping on a dirty strop. Try lighter finishing strokes and clean leather.
  • Spine wearing unevenly: the razor may not be straight, or pressure is uneven. Tape can help limit further wear.
  • Small chips visible: go back to the coarse stone and remove them before progressing.

When to use a honing service instead

A professional honing service is worth considering if:

  • You’re new to straight razors and still learning to shave
  • The razor is valuable or sentimental
  • The blade is warped, heavily worn or chipped
  • You’ve tried honing and the razor still won’t shave comfortably

Many shavers use a service for the first few honings, then learn to maintain the edge themselves with a fine stone and strop. For the rest of the maintenance routine, see straight razor care and maintenance.

The complete guide to straight razor gear

Best Straight Razors
Read the guide

Keep exploring

Guides from other topics

All topics →