The short answer
Most people get a good result with two or three passes:
- With the grain, to reduce most of the stubble
- Across the grain, to get closer
- Optionally, against the grain, for the closest finish, if your skin tolerates it
Reapply lather before each pass. If you have sensitive or bump-prone skin, one or two passes (with and across) is often the better choice.
What counts as a pass?
A pass is one complete trip over the whole area you’re shaving, in one direction relative to your hair growth. Lather, shave the whole face in that direction, rinse, relather, then shave again in the next direction.
The idea is beard reduction: rather than trying to remove everything in one go, you take the stubble down in stages. That’s gentler on the skin and gives a closer result.
Map your beard grain first
Hair doesn’t grow in one direction across your face. It typically grows downwards on the cheeks, but on the neck and under the jaw it often swirls or grows sideways or upwards.
To map it:
- Let a day or two of stubble grow.
- Run your fingers over each area in different directions.
- The direction that feels smoothest is with the grain. The roughest is against the grain.
- Note the areas where direction changes, especially the neck. Some people take a photo or sketch a simple map.
You’ll only need to do this once, and it makes every pass more effective.
The three passes explained
With the grain (WTG)
Shave in the same direction the hair grows. This removes the bulk of the stubble with the least irritation. For beginners, a single WTG pass is plenty for the first week or two while learning the right blade angle.
Across the grain (XTG)
Shave at roughly 90 degrees to the growth direction, often ear-to-nose or nose-to-ear on the cheeks. This picks up much of what the first pass missed and gives a noticeably closer result. Some people do both directions across (two XTG passes) instead of going against.
Against the grain (ATG)
Shave in the opposite direction to growth. This gives the closest, smoothest result, but it’s also the pass most likely to cause irritation, razor burn and ingrown hairs. Only go ATG once your WTG and XTG passes are comfortable, and skip it entirely in areas that react badly.
How many passes do you need?
Comfortable daily shave
WTG + XTG. Two passes give most people a clean, comfortable result that’s close enough for daily life.
Close shave
WTG + XTG + ATG. Three passes for a very smooth finish, for example before an event. Use a light touch and fresh lather for the third pass.
Sensitive or bump-prone skin
WTG only, or WTG + XTG. People prone to razor bumps, particularly with curly or coarse hair, often do best not shaving too close. Shaving with the grain only reduces the chance of hairs curling back into the skin. See how to stop razor burn and nicks and best safety razors for sensitive skin.
Relathering and touch-ups
- Relather for every pass. A pass on dry or thin lather is a common cause of burn.
- Touch-ups: after your final pass, you may find a few rough spots. Wet the area, apply a little lather, and do a short stroke or two. Some people use a little water or leftover lather; that’s fine as long as the skin isn’t dry.
- Don’t buff. Repeatedly going back and forth over the same spot without lather irritates the skin. If a spot won’t come smooth, leave it for tomorrow.
Passes and razor aggressiveness
The number of passes you need depends partly on your razor:
- Mild razors remove less per pass, so you may need a full three passes for a close shave, but each pass is gentle.
- Aggressive razors remove more per pass, so two passes might be enough, but each is more likely to irritate.
An adjustable safety razor lets you use a higher setting for the first pass and a lower one for later passes, which suits a pass-based routine well. For efficient razors, see what are the most aggressive safety razors?
Longer stubble
On several days of growth:
- Trim first if it’s long, or expect the first pass to take more effort.
- Rinse the razor often; long stubble clogs the head.
- Consider an open comb razor, which handles longer growth well. See open comb safety razors.
- Take the first pass slowly, with short strokes.
Not to be confused with: shaves per blade
People sometimes search “how many passes” when they mean how many shaves a blade lasts. That’s a separate question. Most people get about three to six shaves from a DE blade, though it varies with beard coarseness, blade brand and technique. Change the blade as soon as it starts to tug rather than slice; pushing a dull blade further is a common cause of irritation.
For how passes fit into a complete routine, see our complete safety razor guide.