Loading a double edge blade is the part of DE shaving that worries new users most, but it takes less than a minute once you’ve done it a few times. The method depends on how your razor comes apart, so start by working out which type you have.
Identify your razor type
- Two-piece: the top cap has a threaded stud underneath. The baseplate is fixed to the handle. Turning the handle (or a knob at its base) unscrews the cap. Example: Merkur 34C.
- Three-piece: the cap, baseplate and handle all come apart. The cap’s threaded stud passes through the baseplate and screws into the handle. Example: Edwin Jagger DE89.
- Butterfly (twist-to-open): turning a knob at the base of the handle opens two doors on top of the head. Nothing comes apart.
If you’re not sure, gently turn the handle while holding the head. If the cap rises on a stud and the baseplate stays attached to the handle, it’s two-piece. If the baseplate comes loose too, it’s three-piece. If doors open, it’s a butterfly.
Handling a DE blade safely
DE blades are very sharp on both long edges. A few habits keep your fingers safe:
- Hold the blade by its short ends, between thumb and finger, never along the long edges.
- Unwrap carefully. Most blades come in a paper wrapper. Hold the wrapped blade by the short ends, then slide or peel the paper away rather than pulling it across the edges.
- Work over a towel so a dropped blade doesn’t bounce off the sink.
- Don’t rush.
Both edges of a standard DE blade are the same, so it doesn’t matter which way round it goes. Markings on the blade don’t indicate a direction.
Loading a two-piece razor
- Open the razor. Hold the head and turn the handle (or the knob at the base) anticlockwise until the cap is raised and comes free. On many two-piece razors the cap comes off completely.
- Place the blade on the cap. Turn the cap upside down so its underside faces up. Lower the blade over the threaded stud and alignment posts so it sits flat.
- Put the cap back on the baseplate. Holding the cap and blade together, turn them the right way up and lower them onto the baseplate, guiding the stud into the hole in the handle.
- Tighten. Turn the handle clockwise until snug.
- Check alignment (see below).
Some two-piece razors let you lay the blade directly on the baseplate instead. Either way works as long as the blade sits on the alignment posts.
Loading a three-piece razor
- Take it apart. Unscrew the handle anticlockwise. You’ll have three parts: cap (with threaded stud), baseplate, and handle.
- Turn the cap upside down on a towel or in your palm so the stud points up.
- Lay the blade on the cap, over the stud and any alignment posts, so it sits flat.
- Place the baseplate on top, with the guard side facing the blade, so the stud passes through the hole in its centre.
- Hold the cap, blade and baseplate together between thumb and fingers, by the ends of the head.
- Screw the handle on clockwise until snug.
- Check alignment (see below).
Loading with the cap upside down is the easiest method because gravity keeps the blade in place while you add the baseplate.
Loading a butterfly razor
- Turn the knob at the base of the handle anticlockwise until the doors open fully.
- Lay the blade on the centre bar, between the open doors, so it sits on any locating tabs.
- Turn the knob clockwise to close the doors over the blade until snug.
- Check alignment.
On butterfly razors, the doors must close evenly. If one sits higher than the other, open and reload. For cleaning tips specific to this design, see how to take apart and clean a butterfly safety razor.
Check the blade is seated evenly
Before every shave with a new blade:
- Look at the head from above. The blade’s edge should be visible as an even line along both sides.
- Look from each side. The amount of blade showing beyond the guard should look the same on both sides and along the full length.
- If it looks uneven, loosen the handle slightly, nudge the blade by its short ends so it sits squarely on the posts, and retighten.
Uneven exposure is a common cause of nicks on one side of the face and not the other.
How tight should it be?
Snug, not forced. Turn until it stops with gentle resistance. Overtightening can:
- Strip or damage threads, especially on plated zinc alloy razors
- Bend the blade or distort the head
- Make the razor hard to open next time
If your razor has a knurled knob or handle, finger-tight is enough.
Removing and disposing of a used blade
- Open the razor the same way you loaded it.
- Lift the blade off by its short ends, or tip it out onto a towel.
- Put it straight into a blade bank, a sealed tin or a dedicated container. Many blade packs have a slot for used blades.
- When the container is full, dispose of it according to local guidance.
Never drop loose blades into a bin bag, where they can cut whoever handles the rubbish.
Common loading mistakes
- Blade not on the posts. If it isn’t sitting flat over the alignment posts, exposure will be uneven.
- Baseplate upside down (three-piece). The guard should face the blade, not the handle. Some baseplates are reversible with different sides for different aggressiveness; check which side you’re using.
- Overtightening. Snug is enough.
- Leaving the razor partly open. On a butterfly razor, a knob that hasn’t been closed fully can loosen during the shave.
- Handling the long edges. Always hold blades by the ends.
Once the blade is in, the next step is technique. Our guides to finding the right blade angle and how many passes with a safety razor will help with your first shaves. If you haven’t chosen a razor yet, Merkur 34C vs Edwin Jagger DE89 compares a classic two-piece and three-piece.