Shaving Brushes

How to make a shaving brush?

How to make a shaving brush: choose a ready-made knot, make or buy a handle, drill the recess to set the loft, seal the handle, and glue the knot in with epoxy.

On this page
  1. Quick answer
  2. Four ways to make a shaving brush
  3. What you’ll need
  4. Step 1: Choose your knot
  5. Step 2: Choose or make a handle
  6. Step 3: Drill the knot recess
  7. Step 4: Seal the handle
  8. Step 5: Test fit and set the loft
  9. Step 6: Glue the knot
  10. Step 7: Cure and first use
  11. Common mistakes
  12. Can you tie your own knot?
  13. Reknotting an old brush

Quick answer

Most homemade shaving brushes are made by buying a ready-made knot (the bundle of bristles) and gluing it into a handle. The basic process:

  1. Choose a knot: synthetic, badger, boar or horse hair, in the size you want.
  2. Get a handle. Buy one, turn one on a lathe, or adapt something you already have.
  3. Drill a recess in the top of the handle, slightly wider than the knot base, to a depth that gives you the loft you want.
  4. Seal the handle if it’s wood.
  5. Glue the knot into the recess with waterproof two-part epoxy.
  6. Let it cure fully (often about 24 hours) before using it.

You can also tie your own knot from loose hair, but that’s much harder. Nearly all hobby brush makers start with pre-made knots.

Four ways to make a shaving brush

Route Tools needed Difficulty Notes
Kit: pre-made handle plus knot Glue only Easy The simplest way to get a custom combination
No-lathe handle Drill, saw, sandpaper Easy to moderate Use a dowel, block of wood or other found object
Lathe-turned handle Wood lathe, drill chuck or Forstner bits Moderate The most freedom over shape and material
Reknot an old brush Drill or picks, glue Easy to moderate Gives a vintage or worn-out handle a new life

If you want to turn your own handle from acrylic or resin, our guide on how to make a shaving brush from an acrylic blank goes into the lathe steps in detail.

What you’ll need

  • A knot in your chosen hair type and size
  • A handle, or material to make one
  • A drill and a bit or Forstner bit sized to your knot
  • Waterproof two-part epoxy
  • Sandpaper in a range of grits
  • A water-resistant finish for wooden handles
  • Masking tape or a small rubber band
  • Calipers or a ruler

Step 1: Choose your knot

Knots are sold by hair type, diameter (measured at the base) and sometimes loft and shape (bulb or fan). Things to consider:

  • Hair type. Synthetic is soft and low-maintenance. Badger is traditional and varies by grade. Boar is firm and needs break-in. Horse sits in between. See badger vs synthetic shaving brushes and our badger hair grades explainer.
  • Size. Knots are commonly sold from around 20mm to 30mm. A 22–24mm knot is a versatile first build.
  • Shape and density. Bulb knots feel firmer, fans softer. High-density knots have more backbone.

Our guide to knot size, loft and shape explains how these affect feel.

Step 2: Choose or make a handle

  • Buy a pre-made handle drilled for your knot size. Several brush makers and hobby suppliers sell them.
  • Make a handle without a lathe. A short length of hardwood dowel or a block of wood shaped with a saw, rasp and sandpaper works. So do some repurposed objects. Some DIY guides even use plumbing pipe reducers. Make sure the material tolerates water.
  • Turn a handle on a lathe from wood, acrylic or cast resin. This gives you the most control.

A handle that fits comfortably between your fingers matters more than looks. Many commercial brush handles are roughly 45–60mm tall, which is a reasonable starting range. Sharpologist’s palm-to-thumb-pad rule is a handy maximum.

Step 3: Drill the knot recess

The recess (sometimes called the knot hole or socket) holds the knot. Two dimensions matter:

  • Diameter: slightly wider than the knot base, so the knot slides in with a little room for glue. Many makers aim for about 1mm or so wider than the knot, but check your knot supplier’s advice.
  • Depth: this controls loft. Deeper recess means shorter loft and more backbone. A shallower one means longer loft and a softer feel.

Drill straight and square to the handle. A drill press or lathe makes this much easier. Some makers add a slight chamfer or rounded edge at the top of the recess so the hair doesn’t rub on a sharp lip.

Step 4: Seal the handle

Wooden handles need protection from constant water. Common choices among hobbyists include cyanoacrylate (CA) finishes, epoxy coatings and marine-grade spar urethane. Apply several thin coats, including inside the recess, and let them cure fully. Acrylic and resin handles generally only need sanding and polishing.

Step 5: Test fit and set the loft

Before mixing glue:

  1. Push the knot into the recess and measure the loft from the top of the handle to the hair tips.
  2. If the loft is too long, drill a little deeper. If it’s too short, add a spacer such as a small disc of wood or plastic in the bottom of the recess.
  3. Check that the knot sits straight and centred.

It’s much easier to adjust now than after gluing.

Step 6: Glue the knot

  1. Wrap the hair near the base with masking tape or a rubber band to keep stray hairs out of the glue.
  2. Mix the epoxy according to the instructions.
  3. Apply glue to the bottom and lower sides of the recess and to the knot base. Use enough to bond the base firmly, but not so much that it wicks up into the working hair.
  4. Press the knot in with a slight twist to spread the glue, check that it’s straight, and wipe away any excess.
  5. Stand it upright while it sets.

Some makers use silicone sealant instead of epoxy so the knot can be removed and replaced later. It holds less permanently, so it’s a trade-off.

Step 7: Cure and first use

Let the glue cure fully before the brush gets wet. Many epoxies need about 24 hours, but follow the product’s instructions. Then remove the tape, wash the knot with mild shampoo, rinse, and let it dry before your first shave. Expect a few loose hairs from natural-hair knots at first. See why is my shaving brush shedding?

Common mistakes

  • Recess too tight. The glue gets scraped off, or the knot base is crushed.
  • Recess too wide. The knot sits crooked or wobbles.
  • Too much glue. It wicks into the hair and creates a stiff, unusable base.
  • Unsealed wood. It swells, cracks or grows mildew.
  • Not test-fitting first. You end up with a loft you didn’t want.
  • Using the brush before the glue cures.

Can you tie your own knot?

Yes, but it’s a specialist skill. Tying a knot means sorting loose hair, aligning the tips, forming the bundle in a mould, and binding and gluing the base. It needs loose hair, a knot-forming cup or mould, and a lot of patience. Most hobbyists find pre-made knots give better results for far less effort.

Reknotting an old brush

If you have a handle you love but a tired knot, you can replace it:

  1. Cut the old hair down close to the handle.
  2. Carefully drill or pick out the old knot and glue. Go slowly to avoid cracking the handle.
  3. Measure the recess and buy a knot to fit, or widen the recess for a larger knot if the handle wall is thick enough.
  4. Glue in the new knot as above.

It’s a satisfying way to extend a brush’s life, and it fits well with an eco-minded shaving routine.

The complete guide to shaving brushes

Best Shaving Brushes
Read the guide

Keep exploring

Guides from other topics

All topics →