Why acrylic for a shaving brush handle?
Acrylic and cast resin are popular handle materials because they:
- don’t absorb water, so they won’t swell, crack or grow mildew like poorly sealed wood can,
- polish to a high gloss without any applied finish,
- come in a huge range of colours, swirls and translucent effects,
- are durable in a wet bathroom for many years.
The trade-off is that acrylics can be brittle and heat-sensitive while you work them, so they need slightly different technique from wood.
This guide focuses on turning an acrylic handle on a lathe. For choosing a knot, sizing the recess and gluing in general, see our broader guide on how to make a shaving brush.
Choosing an acrylic brush blank
Types of blank
Sellers use “acrylic” loosely. Common materials include:
- Cast acrylic (PMMA). Turns cleanly with sharp tools and polishes very well. Some cast acrylics are fairly brittle.
- Polyester resin. Very common for colourful and pearlescent blanks. It can chip if tools are dull or cuts are too aggressive.
- Other cast resins. Hobby casters often use epoxy or polyurethane resins, sometimes with embedded objects. Turning behaviour varies.
- Hybrid blanks. Wood, pine cones or other materials cast in resin. These need care at the boundary between materials.
If you can, ask the seller what the material is and whether it suits brush handles.
Size
Brush handle blanks are larger than pen blanks. Check that your blank is:
- wide enough for your knot diameter plus a solid wall around the recess, so the handle can be shaped without breaking through, and
- long enough for your handle height plus extra material for holding it in the chuck and parting off.
Many sellers offer blanks sized specifically for brush handles, often around 50mm (2 inches) square or round. Smaller blanks may suit travel brushes with small knots.
Tools and supplies
- Wood lathe with a scroll chuck (and suitable jaws)
- Drill chuck for the tailstock, with a Forstner bit or drill bit sized to the knot
- Sharp turning tools. Many people use carbide-tipped tools for acrylic, while others prefer sharp gouges and scrapers
- Calipers
- Wet-and-dry abrasives through very fine grits, plus micro-mesh pads if you have them
- Plastic polish or a buffing compound suitable for acrylic
- Waterproof two-part epoxy and masking tape for gluing the knot
- Your knot
Safety first
- Wear a full face shield. Acrylic can chip or shatter if a catch occurs.
- Use dust protection. Fine plastic dust from sanding shouldn’t be inhaled. Wet sanding helps reduce it.
- Keep sleeves and hair secured away from the spinning work.
- Check the blank for cracks or voids before mounting it.
- Start at a modest speed and increase only once the blank is round and balanced.
Follow your lathe manufacturer’s guidance on speeds for the size of piece you’re turning.
Step-by-step
1. Plan your dimensions
Decide your knot diameter, loft and handle height before you start. Your loft is set by how deep you drill the recess, so you need to know your knot’s total length. Our guide to knot size, loft and shape explains how these numbers change the feel.
2. Mark and mount the blank
Find and mark the centre on both ends. Mount the blank securely in the chuck. If it’s square, you may need to turn a short tenon first, or mount it between centres to round it before chucking.
3. Drill the knot recess
Drilling the recess first, with the blank held in the chuck and the bit in the tailstock, keeps the hole centred and lets you shape the outside around it.
- Use a sharp bit. Dull bits generate heat, which can melt or crack acrylic.
- Run the lathe slowly while drilling.
- Advance in small steps and back out often to clear chips and let heat escape.
- Drill to your planned depth, measuring as you go. Deeper means shorter loft.
- Size the hole slightly wider than the knot base, often around 1mm, to leave room for glue. Follow your knot supplier’s advice if they give one.
Some turners lightly chamfer or round the top edge of the recess so it doesn’t press a sharp lip into the hair.
4. Rough and shape the handle
- Use light cuts with sharp tools. Heavy cuts or dull edges can cause chips and catches.
- Acrylic shavings often come off as long ribbons. Stop and clear them so they don’t wrap around the work.
- Keep an eye on wall thickness near the recess, and check with calipers.
- Shape a comfortable grip. Gentle waists, flares and rounded transitions are common, and they suit both face and bowl lathering.
5. Wet sand
Acrylic rewards patient sanding:
- Work through progressively finer grits, keeping the surface wet to reduce heat and dust.
- Use low to moderate lathe speeds while sanding, and keep the paper moving.
- Wipe the surface between grits and check for scratches under good light. Go back a grit if any remain.
- Many turners finish with micro-mesh pads up to very fine grades.
6. Polish
Apply a plastic polish or acrylic-safe buffing compound with a soft cloth or pad while the lathe turns slowly. A good acrylic polish job gives a deep gloss without any lacquer.
7. Part off and finish the base
Part the handle off carefully, leaving a little extra material at the base. Then reverse-mount it (on a jam chuck or a padded jaw that grips the recess or the outside) and turn, sand and polish the base to match. A slightly concave or flat base helps the brush stand upright.
8. Glue in the knot
- Test fit the knot and confirm the loft.
- Tape the hair near the base so glue stays off the working hair.
- Apply waterproof two-part epoxy to the recess and the knot base. Don’t use so much that it wicks into the hair.
- Seat the knot straight, wipe off excess glue, and stand the brush upright to cure.
- Wait for a full cure (often around 24 hours) before using the brush.
Wash a new natural-hair knot with mild shampoo before the first shave, and expect a few loose hairs at first. See why is my shaving brush shedding?
Troubleshooting acrylic turning
| Problem | Likely cause | What to try |
|---|---|---|
| Chips or cracks at the rim | Dull tools, heavy cuts, heat while drilling | Sharpen, take lighter cuts, drill slower in steps |
| Melted or cloudy surface | Too much heat from sanding or polishing | Slow down, keep it wet, use less pressure |
| Scratches visible after polishing | Skipped grits | Go back to the last grit that removes them |
| Off-centre recess | Blank not centred, or drill wandered | Drill with the blank in the chuck and the bit in the tailstock |
| Knot sits crooked | Recess too wide or not square | Check alignment while gluing, or fill the gap evenly with epoxy |
Buying pre-drilled or pre-turned options
If you don’t have a lathe, or want to skip the turning, some suppliers sell pre-drilled blanks or finished handles ready for a knot. You still get to choose the knot and its loft, which is where much of a brush’s character comes from. Once it’s built, care for it like any brush. See how to clean a shaving brush.